Community Brag Posts

Modified Farmhouse style bad. Used lighter wood for headrest and footrest. Changed measurements for Lithuanian size of mattress (200x160cm). For headboard panel were used pallets wood so it was necessary to paint it right. Also Added some trims for decorating edges.

I made two of these as gifts. I modified the plans for a smaller bench length and width. They are 33in long on the top with a 1.5 overhang. I chose to place the 1x4 on top at the end as it was easier to stain and finish. Instead of wood glue since it was finished I used 3 pocket hole screws in the back, 2 corner braces with antique bronze finish on the ends under overhang and 2 on the inside of the storage area and gorilla glue.this made it very solid. It also made positioning it easy as I screwed the corner braces to the bottom side of the 1x4 face. I measured for a 1in overhang and 3/4 of an inch for the thickness of the back board. By doing so I could simply place the board on top of the bench and center it for 1.5 in overhang on ends then simply screw in the remaining screw hole in the inside of the storage  compartment.

Designed from the Grandy Sliding Door console, but I modified it by extending it to 8ft wide, and added a media shelf to not cover remote sensors for my set top boxes. This is my first build from Ana White so it took a little more time and expense than I hoped only because of some startup tools I decided to get to help the process.

I made this this February for my daughter’s birthday. I did not use Ana’s plans for same desk since at the time I did not know this site existed. I made my own plans that were influenced by Ballard design and Pottery Barn catalogs. It took me many nights though if you have the time it should not take more than a weekend to make.
I added a keyboard shelf using special slides hat I found at HD.

I made it out pine and plywood from HD. I trimmed the bottom with a trim and painted with primer and high gloss White Dove Valspar paint.

Great, fun project. Only used a Kreg jig, Skill Saw and Sander. Super easy.

This is a 5x5ft square farmhouse table that I built for my dining room. It's all kiln dried construction lumber. I bought a thickness planer to get this right. I got tired of the twists in the boards that made it impossible to get the table top flat and consistent. It's completely worth it. I cut all the boards down from 2x12 lumber to 10 inch width. I routered the edge of each plank with 1/8 bit to give it a small crack in between the planks. I sprayed the new varathane poly, water-based, and it came out perfect. I ended up with 4 coats.

Really enjoyed the build.

You don't really need a Brad nailer or stapler, I did it with good old hammer and nails. Just brace it well when nailing into unsupported beams. You also don't need a tablesaw, I did all the plywood cuts with a circle saw. The shelves in the original plan are deceptively small. After building one side with the shelves how the plan has them, I decided to build the other cart with only one shelf for two on each side instead of four, gives a lot more space. I didn't add any shelves to the other side of the left cart, planning on adding hooks to hang extension cords and such in there. Make sure you predrill, I still had cracking issues even with the self drilling screws. I would recommend splurging on quality plywood especially for the tops and front. 

I plan on adding a dust hood and shelves above each side. Also going to do the tablesaw and bench tool mods to the carts when I get those tools. 

We loved the Tryde coffee table, but thought a more industrial look would fit better in our apartment. We saw some black iron pipes at Home Depot and decided to use these for the legs. It turned out great and looks really good with the rest of the furniture! Thanks for the plan!

So my sister's house is on a rural, sandy lot. Did I mention sand...lots of sand. Her tile doesn't react well to sand-covered shoes , so they needed a place for guests to take off street shoes to replace them with spa booties. I offered to build them a storage bench for that purpose.
I modified the bench to make it shorter as per my sister's request. She also wanted the lower shelf modified to place a boot tray on it to catch the sand. I suggested replacing the lower shelf with rails to place the shoes on so the sand could fall off onto the boot tray. We nailed finish nails into the legs under the rails and slid the tray onto them. Now she can remove the tray easily to dispose of the...sand.
The finish on the body matches the mirror, which hangs above it. The lid of the bench was stained to match the finish on the doors, posts, etc. I used wrap around inset hinges from here: http://www.rocklerpro.com/product.cfm?page=5135&rrt=1
I checked this as a weekend project because of dry time for stain and poly.
Thank you, ANA for the awesome plans.

The goal of this project was to create a buffet / serving table to compliment the large farmhouse table I made a while back.   We have been using a folding table for a buffet line at large family gatherings and that just didnt seem right when placed next to the giant 10' table.  (info for the table: http://www.ana-white.com/2014/07/big-farmhouse-table)

The build is similar to the farmhouse table, but the materials are a bit smaller due to the size of the table.  The legs are 2x3's and the table top itself is made of 2x6's outlining a 2' x 5' section of tile. All of the other materials (stretchers and apron) are made from 1x3s.  The tile is set so it sits about 1/8" higher than the wood.  This is to allow hot pans and plates to be placed directly on the tile without a trivet or other separator.  The tile sets on a 3/4" piece of MDF supported by small 1x2 slats underneath.

All of the joinery is accomplished with glue and Kreg Jig / Screws. 

Total Cost $800

Our local Habitat for Humanity puts on an annual event where they get folks to restore discarded or worn down furniture and sell them at auction. My wife and I participated last year and this year I was asked to build 4 dog houses and then they were going to let local designers/decorators finish them out.

I figured it would be easy to find a good dog house plan, but I was wrong so I had to come up with my own designs. I did not want to use plywood becauase I wanted them to look good. So I used 1x4's and 1x6's. I built them all just a little bit different, but the same basic design on all 3. Since I am not very good with circular cuts, did not do any fancy 1/2 circle doorways!

There are "after" pictures on the Blog. Thanks for looking!

This was my first furniture build & the plans were a great help. Learned a lot along the way, made a few minor changes (1x4 on front of seat gives a little overhang) & had a lot of fun with the project. Our 2 kids are equally proud.

Made this for my granddaughter Reagan's American Girl doll.  I made the bed and my wife made the sheets and blanket and pillow.  Your plans were awesome!

Outdoor console using this plans, but reduced slightly in width

Me and my husband had only a hollywood frame forever and just never wanted to spend the money to buy one, then I found this website!! This is the first thing that I ever built I'm pretty proud of my self. Espically since I had the help of my one and two year old it took a little longer but i got it done.

This project was a true labor of love by a first timer. We are first time homeowners and built our home, which was completed spring of this year. Like most wives, I wanted all the bells and whistles in this home. The bells and whistles add up, and next thing you know, we're eating most of our meals on our granite island upgrade, instead of a new dining set. My husband took it upon himself to purchase tools off of Craigslist and research online for modern farm table plans. He came across Ana's site and loved how she broke everything down in her plans. This was the plan he used http://ana-white.com/2009/11/plan-modern-farmhouse-table-knock-off.html The cutting, sanding, and putting the table together took about four to five hours, but staining and waiting around made the project about twenty hours. Also, everything cost $50 on our end, whereas, the West Elm table I wanted is $700. I'm one happy lady, especially since I think our table looks way better than the one from West Elm. I'm excited to report that my husband is currently refurbishing chairs to go with this beautiful table! Thanks a million for your easy to comprehend plans, Ana. You're the best. Here is a post where I featured my favorite piece of furniture http://www.AnnieAtoZ.com/2013/09/diy-modern-farmhouse-table.html