Community Brag Posts

Well, this crib is STILL unfinished, and the date-stamp says I built it December 5th.... So... Uhh.. I should really get on that!

I had initially built this crib for a friend's daughter's birthday gift, but the baby (8 months old at the time) got REALLY sick, so I wasn't able to finish it in time (don't worry, we got her a Pillow Pet - she got a gift still!). It was just before Christmas, so instead of going out and spending more money that we were tight on, I just bought 3 1x2s and used scraps for the rest of it.

The crib's basically been sitting in the baby's room looking cute until about a month ago. That's when she decided that her stuffed owl (from Build-A-Bear) needed to be put to bed every night before I put HER to bed. It's become such a routine that I have no idea how she'd react if we couldn't put her owl to bed! So I'm scared to try to start filling all the holes and painting in fear that we'd have a mental breakdown if I didn't finish in time for bed! EEK!

I added arms to the stackable chairs. This table and 8 chairs set came out great and I was able to build everything (including the chair cushions found on clearance) for under $350.00 thanks to this website!

This is built off the Farm House X Table but I changed a few things around. The lower support beam has been raised up to the middle of the table. The table height has been raised to 40". The top of the table is floating. The top most 2x4s are secured directly to the top. They are also notched out a little to match the notch I put into the top support beam. The 2x4 is the female side and the support beam is the male. I finished the table by burning the top with a hand held torch and 2 coats or varnish. The base of the table has been white washed with 1 good coat.

Was easy to make

I made this chair for my 3 year old son's Birthday, he loves it. Really easy build.

The square table project obviously modified the original plans a bit. We always use 4" brackets to further stabilize and level our tops. This table we used L brackets on the insides at the top of the trestles. The final finish was Minwax Special Walnut for the tops and an antique white that we color matched for our client. Oh and SEVERAL coats of poly to seal her and make her pretty!

This table was table number 22 that we have built from the plans provided here. We have modified widths, lengths and heights many times over! Come find us on Facebook book or follow us on Pinterest. Just put a /youreunique after and you are there. I would be happy to give tips on our finishes if you email me or send me a PM. Thanks for looking and have a blessed day!

Built this bed from the look of the project done by Ana. Used 4x4s for the legs and used a router to make slots for the 1x8s to fit in. Everything was built as I went because our house was built in 1907 and nothing is square and it also has vaulted ceilings. 

Picnic table

We really liked the plans for this table, but it was too narrow for our taste. My husband altered the plans so that the table is 36" wide. The solid oak boards on the table top are reclaimed from the old barn out back.

I built this dresser for a little girl. It was my first time doing drawers and I was a little intimidated but it wasn't bad at all! I'm going to be building one for my sons room too. Thanks for the great plans!!

I included some pictures of very rudimentary drawings I did of all the cuts of wood you would need to build these if anyone wants to take a stab at it.  The drawings are rudimentary but you can definately build from them

Another idea I got from the kentwood posts.  Actually this was a brag from another user that got the idea from the kentwood nightstand post.  So I took to building it.  It is built out of solid pine.  For middle shelf and bottom shelf are cut from 3/4 thick plywood as my local store didnt cary pine large enough for the shelves and I did not feel like gluing slabs of pine together.  Though I ending up putting slabs of pine together for the top, because I wanted that to be pine like the rest of the nightstand.  I drilled a few pocket holes in each piece of pine.  Glued the edges and screwed them together with pocket holes which worked out great and I didnt have to clamp and wait for them to dry.  The inlay on the door is something I found at my local home depot.  It I glued it on and put a couple of pin nails around the eadges.

I finished the night stands with a cream white latex paint and glazed over the paint with valspar antiquing glaze which gave it a great ages grayish look.  Then sprayed it with a couple coats of Varethane Soft Touch Matte Polyurethane.  Which I dont recomend using.  I only used it because it was the only matte poly I had laying around.  If I were you I would opt for a much better poly to go over waterbased paint like General Finishes High Performance Poly.  The top I stained with General Finishes java gel coat and Gel coat poly.  I wasnt digging the way the gel coat looked on the pine nor did I like the color of the stain paired with the color of the nightstands.  so I have since then sanded off the gel coat and stained the top an onyx which to me looks a lot better.  Sorry I do not have any pictures of that.

I absolutely love how this turned out! Great plans! I used a lot of old wood my grandfather had so this project was extra special. 

I built this for my son's bedroom, but modified it to fit our needs. It is 42" high, 38" wide, and 18" deep. I did a double thick top, which I love, and my Dad routed it for me. This piece is solid! I am very happy with the result! Sorry for the not so great cell phone pics!

My first build, a small side table for our newly decorated guest bedroom. Adapted from the Mini Farmhouse Bedside from Ana's website and the side table from her book.

The top and shelf were made from reclaimed oak panels from an old wardrobe.

I now have a second table and a farmhouse bed to make. I constructed without a Kreg jig but am thinking of buying one now to make construction cleaner.

I had this wine refridgerator that my wife gave to me years ago for a birthday and it really needed a home since it's been sitting in the corner of our dining room for several years.  After seeing some of the adaptations of the Printer Cabinet, I decided to try to modify if for my use.  I put pencil to paper and came up with a two sided design that would hold the refridgerator and all of our wine/bar glasses as well as some liquor.  It came out much better than I expected since this was my first real go at making any kind of cabinetry.  Measure twice, cut once really works.  I am eager to start my next project.  Thanks for the inspiration!

I built this Fancy Hall Tree with cherry hardwood and cherry plywood. The lower bench is done with rabbet joints and dados instead of pocket hold screws but the upper portion is all pocket hole screwed together but instead of laminating a large piece of plywood tot he back I cut individual panels and dropped them into rabbets like a picture in a frame.  The supporting wings are connected to the base and the back panel with pocket screws as is the panel to the base.